Lcd-digital M6000 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Notebooky Lcd-digital M6000. LCD Digital M6000 User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 18
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
DISASSEMBLY PROCEDURE
Chapter
3
Disassembly Procedure
Please follow the information provided in this section to perform the complete
disassembly procedure of the notebook. Be sure to use proper tools
described before.
A
SUS M6000 Series Notebook consists of various modules. This chapter describes the
procedures for the complete notebook disassembly. In addition, in between procedures,
the detailed disassembly procedure of individual modules will be provided for your
service needs.
The disassembly procedure consists of the following steps:
Battery Module
Optical Drive Module
HDD Module
Second Memory Module
CPU Module
Keyboard Module
First Memory Module
Mini PCI Module
LCD Module
Top Case Module
Motherboard Module
Bottom Case Module
3 - 1
Zobrazit stránku 0
1 2 3 4 5 6 ... 17 18

Shrnutí obsahu

Strany 1 - Disassembly Procedure

DISASSEMBLY PROCEDURE Chapter 3 Disassembly Procedure Please follow the information provided in this section to perform the complete disassembly proce

Strany 2 - Second Memory Module

DISASSEMBLY PROCEDURE M2*3L 7. Detach the right & left antenna and its cable. 8. Reomve the speaker cable, then

Strany 3 - Keyboard Module

DISASSEMBLY PROCEDURE 10. Remove 1 screw (M2.5*4L(K)) and 1 screw on the other side, then take right and lift hinge off. M2.5*4L M2.5*4L 11. Rem

Strany 4 - 3 - 4

DISASSEMBLY PROCEDURE M2*3L M2*3L Top Case Module The illustrations below show how to disassemble and remove the top case module of the notebook. R

Strany 5 - CPU Module

DISASSEMBLY PROCEDURE Removing touch pad 3. Loosen the touch pad FPC cable then separate the top case module from the bottom case modu

Strany 6 - Mini PCI Module

DISASSEMBLY PROCEDURE 2. Take the VGA heat sink module away and remove 2 tapes then disconnect modem cable. M2*6L MOTHERBOARD REMOVAL 3.

Strany 7 - LCD Module

DISASSEMBLY PROCEDURE M2*6L 5. Take the optical drive FPC away and remove 6 screws(M2*6L(K)). M2*6L 6. Remove the audio FPC and pull out t

Strany 8 - Disassembling LCD Module

DISASSEMBLY PROCEDURE Bottom Case Module BOTTOM CASE MODULE The illustrations below show how to disassemble and remove the bottom case module of

Strany 9

DISASSEMBLY PROCEDURE M2*3L 4. Remove 1 screw (M2*6L(K)) then remove the MIC out the hole and pull out the audio board upward then take it away. M

Strany 10 - 3 - 10

DISASSEMBLY PROCEDURE 7. Remove 1 screw (M2*6L(K)) and 1 screw on the other side and then take 2 speakers away. M2*6LM2*6L 8. Finally, Remove

Strany 11 - M2.5*4L

DISASSEMBLY PROCEDURE Battery Module BATTERY The illustration below shows how to remove the battery module. 1. Press latch to open the battery modu

Strany 12 - Top Case Module

DISASSEMBLY PROCEDURE M2*3L Optical Drive Module OPTICAL DRIVE REMOVAL Press latch here then pull it out. Keyboard Modul

Strany 13 - Motherboard module

DISASSEMBLY PROCEDURE 2. Unlock 3 keyboard latches then pull out the keyboard forward and lay the keyboard on the front side . 3. Remove 2 screws o

Strany 14 - 3 - 14

DISASSEMBLY PROCEDURE M2*3L CPU Module CPU MODULE REMOVAL The illustrations below show how to remove the CPU module from the notebook. Removing C

Strany 15 - 3 - 15

DISASSEMBLY PROCEDURE First Memory Module FIRST MEMORY MODULE REMOVAL The first memory module is under keyboard. Open the two latches to pop up memory

Strany 16 - Bottom Case Module

DISASSEMBLY PROCEDURE LCD Module LCD MODULE The illustrations below show how to remove and disassemble the LCD module. The module contains LCD panel,

Strany 17 - 3 - 17

DISASSEMBLY PROCEDURE 4. Remove 2 screws(M2.5*6L(K)) at top side, then lift the LCD module away from the system. M2.5*6L

Strany 18

DISASSEMBLY PROCEDURE 4. Disconnect the speaker cable and LCD cable then take Inverter board off. 5. Remove 8 screws (M2*3L(K) x 4 ,(M2*

Komentáře k této Příručce

Žádné komentáře